Lo-Carbon Sentinel Kinetic B

 

Recognised in SAP PCDB

• Ultra quiet

• Lightweight for easier installation

• Horizontal duct option for space-saving installations

• Fits within a 290mm deep kitchen cupboard

• Integrated digital controller for simple and accurate commissioning

• Plug and play controls; Humidistat, Ventwise, Wireless Remote

• BMS connectivity

• LS inputs (Light Switch)

• SEC Class A

• Horizontal duct options

Select a product

Easy Installation

The Sentinel Kinetic models can be mounted vertically in a roof space, hallway cupboard or kitchen or within a kitchen cupboard. When mounted in an unheated area ducting and MVHR unit should be insulated. Ducting can be attached to the unit horizontally, vertically or both. Minimum internal depth of kitchen cupboard: V, B & BH models 290mm.

Left (L) or right (R) hand installation. The unit is supplied with duct spigots to outside on the right hand side. These can be reversed on site by simply removing the control panel, rotating the unit 180 degrees and re-attaching the control panel.

 

Spigot Options

The combination of spigot options allows installation in confined locations. If vertical and horizontal connection is required on the same outlet/inlet, additional spigots can be supplied. The condensate drain can be taken out through the back, side or bottom of the unit. Using the fittings supplied, the final condensate connection is made outside the unit and can be completed after installation.

Integral Humidity Sensor (BH Models)

The integral humidity sensor increases speed in proportion to relative humidity levels, saving energy and reducing noise. The sensor also reacts to small but rapid increases in humidity, even if the normal trigger threshold is not reached. This unique feature ensures adequate ventilation, even for the smallest wet room. The night time relative humidity setback feature suppresses nuisance tripping as humidity gradually increases with falling temperature.

 

Click here for technical information, within our Online Product Selector. After, select your required fan model from the list to display Performance, Sound, Dimensions and Electrical Data.

PRODUCT SPECIFICATION:

 

 
 
Image of Sentinel Kinetic BH
Sentinel Kinetic BH

High efficiency, compact, SAP PCDB eligible, residential Mechanical Ventilation with Heat Recovery unit. With Summer Bypass and Integral Built-In Humidistat.

Please call 0344 856 0590 for further availability information.
Image of Sentinel Kinetic BH Left
Sentinel Kinetic BH Left

High efficiency, compact, SAP Appendix Q eligable, residential Mechanical Ventilation with Heat Recovery unit. With Summer Bypass and Integral Built-In Humidistat.

Please call 0344 856 0590 for further availability information.
Image of Sentinel Kinetic B Standard Filter
Sentinel Kinetic B Standard Filter

ISO 45% Coarse (G3) (2 pack). Formally known as G3, this filter will provide the minimum required filtration.

Replacement filter set comprising 2 filters for the Kinetic B, BH, E, V and Cooker Hood units. Installation instructions included.

Please call 0344 856 0590 for further availability information.
Image of Sentinel Kinetic Wired Remote Controller
Sentinel Kinetic Wired Remote Controller
The Kinetic Wired Remote Controller duplicates all the functions of the on-board controller allowing the unit to be commissioned, controlled and monitored remotely. The controller is supplied with 15 metres of four core cable fitted with an RJ11 plug for fitting to the Kinetic control pcb.
Please call 0344 856 0590 for further availability information.
Image of Wireless enable kit
Wireless enable kit
The Wireless enable kit allows the Kinetic to be set to boost or purge from a remote wireless switch. One switch is supplied with the kit. Up to three additional switches may be linked to the wireless receiver.
Please call 0344 856 0590 for further availability information.
Image of Wireless Transmitter Controller
Wireless Transmitter Controller
• Additional controller for 441865 and 439352 • A maximum of 4 controllers can be used per system • Can be connected to other accessories (eg Humidistat) to send a boost signal wirelessly
Please call 0344 856 0590 for further availability information.
Image of LED Indicator
LED Indicator
Compatible with the Sentinel Kinetic range, the LED Indicator illuminates when the MVHR unit requires a filter check or if the unit has a fault. Supplied with 15 metres of cable. 85 x 85 x 10mm (H x W x D)
Please call 0344 856 0590 for further availability information.
Image of Trickle Boost Switch
Trickle Boost Switch
A single gang switch to boost from high to low speeds on heat recovery systems. 85 x 85 x 10mm (H x W x D)
Please call 0344 856 0590 for further availability information.
Image of Vent-Axia Visionex PIR
Vent-Axia Visionex PIR

A wall or ceiling mounted movement detector for use with any domestic Vent-Axia mains voltage product. Also suitable for use with Vent-Axia T-Series controllers on ‘Auto’ setting and ITC controllers on sensor mode. Visionex PIR can be wired for either On/Off or Trickle/ Boost operation.

  • Fits any UK single gang mounting box.
  • Adjustable timer overrun (5-25 minutes).
  • Range of detection up to 10 metres.
  • Designed to meet IP43.
  • Ambient operating temperature range 0°C to +50°C.
  • Maximum load: 2.5 amps/600W inductive. Not suitable for use with lighting.
  • Internal use only.
  • No switched live required for internal rooms and WCs.
  • Double insulated.
  • Volt-free contacts.
  • Supply voltage 220-240V/1/50Hz.
Please call 0344 856 0590 for further availability information.

 

Raadpleeg de tab Downloads voor technische informatie

 

 

ESTIMATED RUNNING COSTS

Calculate estimated running costs for this product using the tool below.
For average costs, leave the default values in place or enter your own figures in the boxes to recalculate.
Where a product has multi speeds, a typical installation has been used for the below calculations.


pence
(Your current electricity cost in pence per hour. This will be listed on your electric bill)
hours
(The average number of hours per day fan to run in Trickle mode)
hours
(The average number of hours per day fan to run in Boost mode)

Based on the inputted figures, estimated running costs would be:

Overview

Easy Installation

The Sentinel Kinetic models can be mounted vertically in a roof space, hallway cupboard or kitchen or within a kitchen cupboard. When mounted in an unheated area ducting and MVHR unit should be insulated. Ducting can be attached to the unit horizontally, vertically or both. Minimum internal depth of kitchen cupboard: V, B & BH models 290mm.

Left (L) or right (R) hand installation. The unit is supplied with duct spigots to outside on the right hand side. These can be reversed on site by simply removing the control panel, rotating the unit 180 degrees and re-attaching the control panel.

 

Spigot Options

The combination of spigot options allows installation in confined locations. If vertical and horizontal connection is required on the same outlet/inlet, additional spigots can be supplied. The condensate drain can be taken out through the back, side or bottom of the unit. Using the fittings supplied, the final condensate connection is made outside the unit and can be completed after installation.

Integral Humidity Sensor (BH Models)

The integral humidity sensor increases speed in proportion to relative humidity levels, saving energy and reducing noise. The sensor also reacts to small but rapid increases in humidity, even if the normal trigger threshold is not reached. This unique feature ensures adequate ventilation, even for the smallest wet room. The night time relative humidity setback feature suppresses nuisance tripping as humidity gradually increases with falling temperature.

 

Technical

Click here for technical information, within our Online Product Selector. After, select your required fan model from the list to display Performance, Sound, Dimensions and Electrical Data.

PRODUCT SPECIFICATION:

 

 
 

Models

Image of Sentinel Kinetic BH
Sentinel Kinetic BH

High efficiency, compact, SAP PCDB eligible, residential Mechanical Ventilation with Heat Recovery unit. With Summer Bypass and Integral Built-In Humidistat.

Please call 0344 856 0590 for further availability information.
Image of Sentinel Kinetic BH Left
Sentinel Kinetic BH Left

High efficiency, compact, SAP Appendix Q eligable, residential Mechanical Ventilation with Heat Recovery unit. With Summer Bypass and Integral Built-In Humidistat.

Please call 0344 856 0590 for further availability information.
Image of Sentinel Kinetic B Standard Filter
Sentinel Kinetic B Standard Filter

ISO 45% Coarse (G3) (2 pack). Formally known as G3, this filter will provide the minimum required filtration.

Replacement filter set comprising 2 filters for the Kinetic B, BH, E, V and Cooker Hood units. Installation instructions included.

Please call 0344 856 0590 for further availability information.

Accessories

Image of Sentinel Kinetic Wired Remote Controller
Sentinel Kinetic Wired Remote Controller
The Kinetic Wired Remote Controller duplicates all the functions of the on-board controller allowing the unit to be commissioned, controlled and monitored remotely. The controller is supplied with 15 metres of four core cable fitted with an RJ11 plug for fitting to the Kinetic control pcb.
Please call 0344 856 0590 for further availability information.
Image of Wireless enable kit
Wireless enable kit
The Wireless enable kit allows the Kinetic to be set to boost or purge from a remote wireless switch. One switch is supplied with the kit. Up to three additional switches may be linked to the wireless receiver.
Please call 0344 856 0590 for further availability information.
Image of Wireless Transmitter Controller
Wireless Transmitter Controller
• Additional controller for 441865 and 439352 • A maximum of 4 controllers can be used per system • Can be connected to other accessories (eg Humidistat) to send a boost signal wirelessly
Please call 0344 856 0590 for further availability information.
Image of LED Indicator
LED Indicator
Compatible with the Sentinel Kinetic range, the LED Indicator illuminates when the MVHR unit requires a filter check or if the unit has a fault. Supplied with 15 metres of cable. 85 x 85 x 10mm (H x W x D)
Please call 0344 856 0590 for further availability information.
Image of Trickle Boost Switch
Trickle Boost Switch
A single gang switch to boost from high to low speeds on heat recovery systems. 85 x 85 x 10mm (H x W x D)
Please call 0344 856 0590 for further availability information.
Image of Vent-Axia Visionex PIR
Vent-Axia Visionex PIR

A wall or ceiling mounted movement detector for use with any domestic Vent-Axia mains voltage product. Also suitable for use with Vent-Axia T-Series controllers on ‘Auto’ setting and ITC controllers on sensor mode. Visionex PIR can be wired for either On/Off or Trickle/ Boost operation.

  • Fits any UK single gang mounting box.
  • Adjustable timer overrun (5-25 minutes).
  • Range of detection up to 10 metres.
  • Designed to meet IP43.
  • Ambient operating temperature range 0°C to +50°C.
  • Maximum load: 2.5 amps/600W inductive. Not suitable for use with lighting.
  • Internal use only.
  • No switched live required for internal rooms and WCs.
  • Double insulated.
  • Volt-free contacts.
  • Supply voltage 220-240V/1/50Hz.
Please call 0344 856 0590 for further availability information.

Downloads

Related Products