lo-carbon-nbr-dmev-c
lo-carbon-nbr-dmev-c

Lo-Carbon NBR dMEV C

  • Continuously running 100mm and 125mm dMEV with sleek circular design
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Near silent operation independently tested
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 56mm (100mm spigot) and 66mm (125mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Intelligent humidistat option with proportional speed increase and timer
  • Comfort control option
  • 7- year warranty

Select a product

Lo-Carbon NBR dMEV C
Increased whole ventilation rates, should not mean increased noise levels. The Vent-Axia Lo-Carbon NBR dMEV C fan, available in 100mm and 125mm, provides adequate ventilation whilst minimising noise.

The fan is designed in line with the Approved Document F 2021 Building Regulations, meeting the increased whole house ventilation rates.

Table 1.3  -  Minimum whole dwelling ventilation rates determined by the numbers of bedrooms.

 

No. of  bedrooms 2013 Edition 2021 Edition Increase
1 13l/s 19l/s 46%
2 17l/s 25l/s 47%
3 21l/s 31l/s 47%
4 25l/s 37l/s 48%
5 43l/s 43l/s 48%

 

The minimum whole dwelling ventilation rate for the supply air should meet the higher of the two following result:

  • A minimum rate of 0.3l/s per m2 of internal floors area
  • A minimum rate determined by the number of bedroom, as per Table 1.3

Nuisance tripping has also been minimised within the fan logic. The integral humidity sensor versions have functionality that allows for proportional speed increase up to 85% relative humidity (RH) before enabling Boost. 

The Lo-Carbon NBR dMEV C is complete with IPX5 rating, allowing flexible installation within Zone 1, 2 and 3.

A back pressure detection system option is available, to Boost if the system pressure increase momentarily due to external wind conditions. A silent mixed flow impeller means the Lo-Carbon NBR dMEV C can meet the requirements of many domestic installations without the need to use a traditional centrifugal fan.

A brand new control platform also provides fully adjustable airflow, meaning wholehouse rates can be achieved easily using fewer fans.

Comfort Control Option
Designed to offer a more relaxing environment to the homeowner, the Lo-Carbon NBR dMEV C features a delayed start. This patented comfort control option allows the homeowner to enjoy a quiet, peaceful bathroom for up to 20 minutes before the Boost activates. Furthermore, if the light switch turns On and Off within three minutes, the Boost will not activate. No more disturbing the family if the bathroom light is turned on during the night.  

Near Silent Operation
The fan has been designed to beas discreet as possible for homeowners, with independently tested sound levels as low as 11.3dB(A) at 6l/s.

 

 

PRODUCT SPECIFICATION:

Sound

Model Flow l/s Min Max
100 dB(A) 7.4 34.3
125 dB(A) 8.5 37.9

 

SAP PCDB Performance 2021

Unit configuration Location 100 Model 125 Model
In room (rigid duct) Kitchen (13l/s) 0.14 0.14
Kitchen/Wet room (8l/s) 0.11 0.12
Through wall Kitchen (13l/s) 0.08 0.09
Kitchen/Wet room (8l/s) 0.08 0.10

DIMENSIONS:

Model A B C D
100 56 54 99 195
125 66 57 120

228

 

 

Image of Lo-Carbon NBR dMEV C 100
Lo-Carbon NBR dMEV C 100
  • Continuously running 100mm fan
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 56mm (100mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498095
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon NBR dMEV C 100 HT
Lo-Carbon NBR dMEV C 100 HT
  • Continuously running 100mm fan
  • Intelligent humidistat option with proportional speed increase and timer
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 56mm (100mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498096
Price £269.62 (excl VAT)
Image of Lo-Carbon NBR dMEV C 125
Lo-Carbon NBR dMEV C 125
  • Continuously running 125mm fan
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 66mm (125mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498097
Price £338.60 (excl VAT)
Image of Lo-Carbon NBR dMEV C 125 HT
Lo-Carbon NBR dMEV C 125 HT
  • Continuously running 125mm fan
  • Intelligent humidistat option with proportional speed increase and timer
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 66mm (125mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498098
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of 100mm Wall Fitting Kits (White)
100mm Wall Fitting Kits (White)

100mm Wall Fitting Kits (White) For installing into most walls using the telescopic liners supplied.

Stock Ref. No: 254102
Price £37.25 (excl VAT)
Image of 100mm Wall Fitting Kits (Brown)
100mm Wall Fitting Kits (Brown)
100mm Wall Fitting Kits in Brown
Stock Ref. No: 254100
Price £37.25 (excl VAT)
Image of 125mm Wall Kit White
125mm Wall Kit White

Wall Kit for suitable for Silhouette 125 models

Stock Ref. No: 455226
Price £41.20 (excl VAT)
Image of Wall Fitting Kit	Brown 125mm
Wall Fitting Kit Brown 125mm
Stock Ref. No: 497434
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Wall Fitting Kit Terracotta 125mm
Stock Ref. No: 497432
(Please call 0344 856 0590 0344 856 0590 for further availability information)

 

Raadpleeg de tab Downloads voor technische informatie

 

 

ESTIMATED RUNNING COSTS

Calculate estimated running costs for this product using the tool below.
For average costs, leave the default values in place or enter your own figures in the boxes to recalculate.
Where a product has multi speeds, a typical installation has been used for the below calculations.


pence
(Your current electricity cost in pence per hour. This will be listed on your electric bill)
hours
(The average number of hours per day fan to run in Trickle mode)
hours
(The average number of hours per day fan to run in Boost mode)

Based on the inputted figures, estimated running costs would be:

Overview

Lo-Carbon NBR dMEV C
Increased whole ventilation rates, should not mean increased noise levels. The Vent-Axia Lo-Carbon NBR dMEV C fan, available in 100mm and 125mm, provides adequate ventilation whilst minimising noise.

The fan is designed in line with the Approved Document F 2021 Building Regulations, meeting the increased whole house ventilation rates.

Table 1.3  -  Minimum whole dwelling ventilation rates determined by the numbers of bedrooms.

 

No. of  bedrooms 2013 Edition 2021 Edition Increase
1 13l/s 19l/s 46%
2 17l/s 25l/s 47%
3 21l/s 31l/s 47%
4 25l/s 37l/s 48%
5 43l/s 43l/s 48%

 

The minimum whole dwelling ventilation rate for the supply air should meet the higher of the two following result:

  • A minimum rate of 0.3l/s per m2 of internal floors area
  • A minimum rate determined by the number of bedroom, as per Table 1.3

Nuisance tripping has also been minimised within the fan logic. The integral humidity sensor versions have functionality that allows for proportional speed increase up to 85% relative humidity (RH) before enabling Boost. 

The Lo-Carbon NBR dMEV C is complete with IPX5 rating, allowing flexible installation within Zone 1, 2 and 3.

A back pressure detection system option is available, to Boost if the system pressure increase momentarily due to external wind conditions. A silent mixed flow impeller means the Lo-Carbon NBR dMEV C can meet the requirements of many domestic installations without the need to use a traditional centrifugal fan.

A brand new control platform also provides fully adjustable airflow, meaning wholehouse rates can be achieved easily using fewer fans.

Comfort Control Option
Designed to offer a more relaxing environment to the homeowner, the Lo-Carbon NBR dMEV C features a delayed start. This patented comfort control option allows the homeowner to enjoy a quiet, peaceful bathroom for up to 20 minutes before the Boost activates. Furthermore, if the light switch turns On and Off within three minutes, the Boost will not activate. No more disturbing the family if the bathroom light is turned on during the night.  

Near Silent Operation
The fan has been designed to beas discreet as possible for homeowners, with independently tested sound levels as low as 11.3dB(A) at 6l/s.

 

 

Technical

PRODUCT SPECIFICATION:

Sound

Model Flow l/s Min Max
100 dB(A) 7.4 34.3
125 dB(A) 8.5 37.9

 

SAP PCDB Performance 2021

Unit configuration Location 100 Model 125 Model
In room (rigid duct) Kitchen (13l/s) 0.14 0.14
Kitchen/Wet room (8l/s) 0.11 0.12
Through wall Kitchen (13l/s) 0.08 0.09
Kitchen/Wet room (8l/s) 0.08 0.10

DIMENSIONS:

Model A B C D
100 56 54 99 195
125 66 57 120

228

 

 

Models

Image of Lo-Carbon NBR dMEV C 100
Lo-Carbon NBR dMEV C 100
  • Continuously running 100mm fan
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 56mm (100mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498095
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon NBR dMEV C 100 HT
Lo-Carbon NBR dMEV C 100 HT
  • Continuously running 100mm fan
  • Intelligent humidistat option with proportional speed increase and timer
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 56mm (100mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498096
Price £269.62 (excl VAT)
Image of Lo-Carbon NBR dMEV C 125
Lo-Carbon NBR dMEV C 125
  • Continuously running 125mm fan
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 66mm (125mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498097
Price £338.60 (excl VAT)
Image of Lo-Carbon NBR dMEV C 125 HT
Lo-Carbon NBR dMEV C 125 HT
  • Continuously running 125mm fan
  • Intelligent humidistat option with proportional speed increase and timer
  • Designed to comply with the latest Building Regulations Parts L1A and F 2021
  • SAP PCDB listed with SFP’s down to 0.08 W/l/s
  • Almost silent operation, sound levels as low as 11.3dB(A) at 6l/s
  • IPX5 rated, wall and ceiling mounted Zones 1, 2 and 3
  • Low ceiling void - 66mm (125mm spigot)
  • Easy to commission, fully adjustable variable control platform
  • Comfort control option
  • 7- year warranty
Stock Ref. No: 498098
(Please call 0344 856 0590 0344 856 0590 for further availability information)

Accessories

Image of 100mm Wall Fitting Kits (White)
100mm Wall Fitting Kits (White)

100mm Wall Fitting Kits (White) For installing into most walls using the telescopic liners supplied.

Stock Ref. No: 254102
Price £37.25 (excl VAT)
Image of 100mm Wall Fitting Kits (Brown)
100mm Wall Fitting Kits (Brown)
100mm Wall Fitting Kits in Brown
Stock Ref. No: 254100
Price £37.25 (excl VAT)
Image of 125mm Wall Kit White
125mm Wall Kit White

Wall Kit for suitable for Silhouette 125 models

Stock Ref. No: 455226
Price £41.20 (excl VAT)
Image of Wall Fitting Kit	Brown 125mm
Wall Fitting Kit Brown 125mm
Stock Ref. No: 497434
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Wall Fitting Kit Terracotta 125mm
Stock Ref. No: 497432
(Please call 0344 856 0590 0344 856 0590 for further availability information)

Downloads